Robe ROBIN Pointe Especificações

1 Version1.7

103.4 Replacing rotating gobos DANGER!Replace gobos with the device switched off only.Unplug from mains before!1. Disconnect the xture from mains and

113.5 Rigging the xtureA structure intended for installation of the xture (s) must safely hold weight of the xture(s) placed on it. The structure

12Truss installation1.Bolt each clamp (1) to the omega holder (3) with M12 bolt and lock nut through the hole in the holder.2.Fasten the omega holder

133.6 DMX-512 connectionThe xture is equipped with both 3-pin and 5-pin XLR sockets for DMX input and output.The sockets are wired in parallel.Only

143.7 Ethernet connectionThe xtures on a data link are connected to the Ethernet with ArtNet communication protocol.The control soft-ware running on

15Ethernet / DMX operationOption “ Artnet" (gMaI or gMA2 or sACN) has to be selected from “Ethernet Mode” menu at rst xture.Option “Ethernet To

163.8 Wireless DMX operationThe wireless version of the Robin Pointe is equipped with the Lumen Radio CRMX module and antenna for receiving DMX sign

174. Remotely controllable functionsLampThe Robin Pointe is to be operated with a Osram Sirius HRI 280W RO lamp. The Osram Sirius HRI 280W RO is a la

185. Control menu mapDefault settings=Bold printTab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Addressing Settings DMX Address 001-255 Ether

19Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Lamp OffFixture PositionFixture Temperatures Head TemperatureAmbient TemperatureBase Temperatures

2Table of contents1. Safety instructions ... 32.

20Tab Level 1 Level 2 Level 3 Level 4 Level 5 Level 6Focus Rot. Gobos 0-255Play Dynamic DemoPlay Static DemoMusicTrigger Off, OnPreset Playback NoneTe

216. Control menu The Robin Pointe is equipped with the QVGA Robe touch screen with battery backup which allows to set the xture´s behaviour accord

22Note: The green icon at the top right corner of the screen indicates the level of the display battery charging. If the whole icon is green, the batt

23 address.The IP uniquely identies any node (xture) on a network. There cannot be 2 xtures with the same IP address on the network! Defaul

24 been fabricated. Maximum Res. - A maximum temperature of the xture head since the counter was last reset. In order to reset this coun

25 Fixture Temperatures - Recorded temperatures which have exceeded dened levels.Note: The log buffer can contain 8000 records max. If the buffer i

26 igoes goes from position to position. Gobo Wheel Moving - The menu item enables to close light output while the rot. gobo wheel goes f

27 Play Dynamic Demo - This option uses all Robin Pointe functions including pan/tilt movement and therefore is good for a complete introduction

286.6 Tab "Service"Adjust DMX Values - The menu allows you to set all effects to desired positions before ne calibration of the effects .Ca

29 After having calibrated all effects, touch the [conrm] to save adjusted values and reset the xture. Load Default Calibrations - The item loads

3FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INITIAL START - UPThis device has left our premises in absolutely perfect cond

30 command. If the lamp is started directly from the control panel, the time delay will be ignored. Lamp Light Sensor - Select this item to switch

311...Another options for this command (only for Robe´s xtures): value PARAMETER_DATA=0x84 - lamp OFF by DMX value on DMX channel value PAR

32position.Prism 2 Rotation Error 1 (Prism 2 Rotation Error 2 )The messages will appear after the reset of the circular prism wheel if this effect is

339. Technical SpecicationsElectrical Power supply:...electronic auto-ranging Input voltage range:... supply

34Control Graphic touch screen for xture setting and addressing Gravitation sensor for auto screen positioning Battery backup of the touch s

35Dimensions (mm)Accessories Omega holder (No.99010420)...2 pcs10. Maintenance and cleaningIt is absolutely essential

36The front objective lens will require weekly cleaning as smoke-uid tends to building up residues, reducing the light-output very quickly. The coo

3712. Photometric diagramsAll diagrams are for full power of the lamp (Standard Mode)

38

39

4If the xture has been exposed to drastic temperature uctuation (e.g. after transportation), do not switch it on immediately. The arising condensati

40

DMX protocol1 2 31 1 1Pan0 - 255 Pan movement by 540°proportional2 * 2Pan Fine0 - 255 Fine control of pan movementproportional3 2 3Tilt0 - 255 Tilt mo

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control230 - 239Lamp Offstep240 - 255Reserved7 5 7Colour wheel Continual positioning0 Open/white

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control1 - 255 Time of colour wheel movement (0.1 sec. --- >25.5 sec.)proportional* * 12Stati

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control244 - 249 Random gobo selection by audio controlstep(Set microphone sensitivity in menu

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control200 - 201 Open/hole step202 - 221 Forwards gobo wheel rotation from fast to slowproport

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control1 - 179 Frost from 0% to 100%proportional180 - 189 100% froststep190 - 211 Pulse closing

DMX protocol1 2 3Mode/channelDMX ValueFunctionType of control0 - 255 Fine dimmingproportionalPage 7

41

52. Fixture exterior view Rear panel of the base:1 - Ethernet input-RJ452 - Power 3 - 3-pin DMX Out 4 - 5-pin DMX Out 5 - Fuse holder-live 6 - Fu

63. Installation Fixtures must be installed by a qualied electrician in accordance with all national and local electrical and const

73.2 Changing the lamp DANGER ! Install the lamp with the xture unplug from mains !To insert the new lamp.1. Disconnect the xture from mains and a

83.3 Lamp adjustment The lamp holder is aligned at the factory. Due to differences between lamps,the ne adjustment may improve light performance.For

9Note!The adjusted hot-spot may move during the rst 100 hours of the lamp operation(lamp stabilizes its burning) and the lamp adjusting has to be rep